The Basics of Plumbing Skills for Bathtub Installation

Click Here

We have found this post relating to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround below on the net and concluded it made sense to relate it with you on this page.

Installing a bathtub isn't exactly brain surgery, but it does need strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is also a reasonably challenging job. If the old bathtub is easily available, the job can move immediately; if you have to open a wall surface to eliminate the old bathtub as well as place the brand-new bathtub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly require a helper to leave the old bathtub and also set in the new one. Make certain you have actually qualified yourself for the job as well as fit trying it. As opposed to working with a professional to take over a halfway-completed job, it is much better to take into consideration using one prior to you start. Possibilities are you may need a professional plumber to make tube connections.
This article will certainly help you mount a new bath tub in your shower room if you have currently purchased a brand-new bathtub and also don't require to alter the setup of your previous water pipes.
Your tools as well as product list should comprise the following:

New Tub

Hammer

Pipe Wrenches

Prybar

Safety Glasses

Degree

Pliers

Adjustable Wrench

Putty Knife

Screwdriver

Cold Chisel

Measuring tape

Pipe Caps

Planning for the Setup

Firstly, the supporting frame supplied with the bathroom ought to be fitted (if called for) according to the maker's instructions. Next, fit the faucets or mixer to the bath tub. When fitting the tap block, it is important to make certain that if the tap includes a plastic washer, it is fitted between the bath as well as the taps. On a plastic bath, it is additionally reasonable to fit a sustaining plate under the taps unit to stop stress on the tub.
Fit the flexible faucet ports to the bottom of the two faucets utilizing 2 nuts and olives (sometimes provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bath. Make use of the nut provided by the supplier to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bath. See to it you make use of every one of the supplied washing machines.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Attach all-time low of the overflow tube in a similar manner.The bath must currently prepare to be suited its last position.

Removing Old Taps

If you need to replace old taps with new ones as a part of your setup, then the first thing you must do is detach the water. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of removing the existing taps can be fairly troublesome due to the limited access that is frequently the instance.
Make use of a container wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a towel ready for the staying water that will certainly originate from the pipelines. As soon as the supply pipes have been gotten rid of, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from transforming during this procedure. As soon as the taps have actually been gotten rid of, the holes in the bath/basin will need to be cleaned of any type of old securing substance.
Before carrying on to fit the brand-new faucets, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new taps to fit.

Setting up the Bathtub

Using both wood boards under its feet, put the tub in the required position. The wood boards are handy in uniformly spreading the weight of the bathtub over the location of the boards rather than focusing all the weight onto 4 small factors.
The next objective is to ensure that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bathtub up until the level reads level.
To mount taps, fit all-time low of the furthest adaptable tap port to the appropriate supply pipe by making a compression sign up with; then do the same for the various other faucet.
Switch on the water system and also check all joints and new pipework for leakages and also tighten them if essential. Fill the bathtub and likewise inspect the overflow electrical outlet and also the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as defined in the supplier's user's manual. Tiling as well as sealing around the tub ought to wait until the bathtub has been used at the very least once as this will certainly resolve it right into its final setting.

Fitting New Touches

If the tails of the new taps are plastic, then you will certainly need a plastic adapter to avoid damage to the thread. One end of the adapter fits on the plastic tail of the faucet and the other end supplies a connection to the existing supply pipelines.
If you require to fit a monobloc, then you will certainly need decreasing couplers, which connects the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in area between the faucet and also the sink. Protect the faucet in position with the producer supplied backnut. As soon as the tap is safely in position, the supply pipelines can be attached to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The former type ought to be linked to the tap ends first, tightening only by hand. The supply pipes can later on be linked to the other end. Tighten both ends with a spanner after both ends have been connected.

Tiling Around the Bath tub

In the location where the bathroom meets the floor tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to fracture an inflexible seal, triggering the water to permeate the wall in between the bath and the tiling, bring about issues with dampness and also possible leakages to the ceiling below.
You can choose from a range of coloured sealers to blend in your components and installations. They are sold in tubes as well as cartridges, and also are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill, you can load it with spins of drenched newspaper or soft rope. Bear in mind to always load the bathtub with water before sealing, to allow for the movement experienced when the bathtub remains in usage. The sealer can split fairly very early if you do not consider this activity before sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to dimension, are likewise easily offered on the market. It is advisable to fit the floor tiles making use of water-resistant or water resistant sticky and grout.

A Step-by-Step Guide to Installing a Bathtub

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

Remove the Existing Bathtub

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

Choose the Right Bathtub

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

Install the Plumbing and Ledger Board

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

Install the Bathtub

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

Hook up the Plumbing

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

Install the Bathtub Surround

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

Do you really like more info about How to Install a Bathtub Yourself? Create a remark down below. We will be delighted to see your suggestions about this blog entry. We are looking forward that you visit us again in the near future. Sharing is caring. Helping others is fun. Many thanks for your time. Visit us again soon.

Protect plumbing integrity; connect now.